全自动剥锌机振打机理分析与试验研究

根据全自动剥锌机组在工业生产上的使用情况,通过分析其振打设备中活塞钎杆模型的振打机理,分析振打锤敲击阴极板面的应力传递关系,初选振打锤基本参数,重新设计振打设备。通过工业试验,采用单因素控制变量法,试验分析振打次数、气压压强、锤心至锌片上边缘的距离,以及这三个因素对振打效果的影响。结果可为今后同类型设备的优化设计提供参考和依据。     

煤巷过断层破碎带施工工艺与支护技术实践

W1313回风顺槽在里程332 m处揭露正断层,对此采取了调整巷道顶板锚网索支护参数,采用圆木大板棚复合支护等措施,并加强了顶板、通风、掘锚机破岩、爆破作业和作业人员的安全管理,确保工作面过断层破碎带时的安全施工。     

智能远距离激光切割控制系统设计与研究

随着人工智能技术的发展,机器视觉与传统工业的结合应用越来越广泛。在电力铁塔安装作业过程中,角钢预置孔位常出现错位,需要在高空实施切割打孔作业。因激光切割角钢效率较高,研制了一套适用于高空铁塔的扩孔切割设备可解决传统方法效率低的问题。通过视觉识别待切割孔,确定待切割路径,控制电机转动,完成激光切割作业。经过试验,所设计的控制系统能够满足激光扩孔切割要求。     

综放面端头及顺槽超前区顶板支护技术与实践

针对虎峰煤业2115工作面开采区煤层上部存在采空区和空巷的情况,结合工作面顺槽架棚支护的现状,通过采用“π”型梁支护管理工作面两侧端头和顺槽超前区顶板。现场实践表明,工作面回采过程中,工作面端头和超前区顶板管理较好,没有出现大面积网兜、落煤和落矸现象,顺槽金属棚能够及时回收,取得了较好的技术经济效益。     

Benchmark value determination of energy efficiency indexes for coal-fired power units based on data mining methods

The operational optimisation of coal-fired power units is important for saving energy and reducing losses in the electric power industry. One of the key issues is how to determine the benchmark values of the energy efficiency indexes of the units. Therefore, a new framework for determining these benchmark values is proposed, based on data mining methods. First, the energy efficiency key performance indicators (KPIs) associated with the net coal consumption rate (NCCR) were selected based on the domain knowledge. Second, the decision-making samples with minimal NCCR were acquired with the fuzzy C-means (FCM) clustering algorithm, and the corresponding clustering centres were employed as the benchmark values. Finally, based on the support vector regression (SVR) algorithm, the target values of the NCCR were obtained with the KPIs as input, and the energy saving potential was evaluated by comparing the target values with the historical values of the NCCR. An actual on-duty 1000 MW unit was taken as study unit, and the results show that the energy saving potential is remarkable when the operators adjust the KPIs based on the calculated benchmark values.     

半纤维素基阿维菌素载药微囊的制备及性能

目前阿维菌素以高效性、无污染和低抗药性等特点而得到广泛应用，但是其稳定性较差，易降解导致使用量较大从而造成浪费。为解决上述问题，本文以半纤维素为基体，利用原位聚合法制备阿维菌素载药微囊（HDCM），通过制备条件、热降解性、储存稳定性和释放动力学研究，确定了HDCM的载药量、热稳定性及释放性能。结果表明，在芯壁比为1∶34（质量比），温度为65℃，pH为3.5的制备条件下，HDCM的载药量可达66.5%，粒径较小且分散均匀。HDCM的热降解性能和恒温热稳定性能较阿维菌素原药有所提高，最高热分解温度从261℃增加到272℃，阿维菌素原药10h后降解率达到12.1%，而载药量为66.5%的HDCM降解率仅为5.2%。HDCM的释放机理满足Fick扩散，阿维菌素原药在水中的累积释放率在12h之内达到83.8%，而HDCM的累积释放率在24h之后才有所增大，12h内其释放率仅为33.7%，表明HDCM具有极好的缓释性能。     

基于极点配置的推力矢量伺服系统控制策略研究

针对推力矢量伺服系统提出了一种采用状态反馈对系统极点进行配置的方法,同时采用该方法设计了Luenberger状态观测器,在此基础上实现了伺服系统的稳态控制。通过仿真和实验表明,采用该方法设计的推力矢量伺服系统的性能优于基于输出反馈的PI-陷波滤波控制的系统性能。     

Robust SVM-direct torque control of induction motor based on sliding mode controller and sliding mode observer

This paper proposes a design of control and estimation strategy for induction motor based on the variable structure approach. It describes a coupling of sliding mode direct torque control (DTC) with sliding mode flux and speed observer. This algorithm uses direct torque control basics and the sliding mode approach. A robust electromagnetic torque and flux controllers are designed to overcome the conventional SVM-DTC drawbacks and to ensure fast response and full reference tracking with desired dynamic behavior and low ripple level. The sliding mode controller is used to generate reference voltages in stationary frame and give them to the controlled motor after modulation by a space vector modulation (SVM) inverter. The second aim of this paper is to design a sliding mode speed/flux observer which can improve the control performances by using a sensorless algorithm to get an accurate estimation, and consequently, increase the reliability of the system and decrease the cost of using sensors. The effectiveness of the whole composed control algorithm is investigated in different robustness tests with simulation using Matlab/Simulink and verified by real time experimental implementation based on dS pace 1104 board.     

NH2-MCM-41的改性及其pH响应性释药的研究

采用正硅酸乙酯（TEOS）和3-氨丙基三乙氧基硅烷（APTES）通过共缩聚法合成介孔二氧化硅（MCM-41）。首先对其氨基修饰，再通过有机合成接枝—R基团（—R：—CHO、—OH、—CH₃、—COOH），制备得到Me-Ph-NH-MCM-41、OHC-Ph-NH-MCM-41、HO-Ph-NH-MCM-41、HOOC-Ph-NH-MCM-41四种不同的药物载体。利用FT-IR、Zeta电位、XRD和SEM对其结构和形貌表征，结果表明NH₂-MCM-41改性成功。以罗丹明B（RhB）为模型进行载药性能测试，并考察了此释药系统在模拟不同pH的体液下的敏感释药行为，同时探究了不同—R基团对释药的影响。结果显示，四种载体在中性条件下几乎不发生药物释放，通过改变环境体系pH可以有效控制药物释放，其释药行为可以用Korsmeyer-Peppas动力学模型来描述。实验表明，释药量：RhB@HOOC-Ph-NH-MCM-41>RhB@OHC-Ph-NH-MCM-41>RhB@HO-Ph-NH-MCM-41>RhB@Me-Ph-NH-MCM-41，不同—R基团的药物载体的pH响应性不同，其中RhB@HOOC-Ph-NH-MCM-41释药量在pH=1.2时可达57.87%，在用于药物智能控释材料方面具有一定的应用潜力。     

XJM-KS型浮选机矿化器负压产生机理研究

浮选机矿化器是用于浮选矿浆预处理的重要设备，其性能的优劣直接影响到浮选机的工作效果。文章通过流体力学仿真软件FLUENT对XJM-KS型浮选机矿化器的内部流场进行数值仿真，重点研究了聚焦式喷嘴布置所带来的流场特征。模拟结果表明，高速的矿浆射流能够在混合室内产生-2.43×10Pa的负压区，从而吸入大量的空气，实现空气与矿浆的有效混合与预矿化，与传统的机械搅拌式矿浆预处理装置相比，该矿化器能够大幅度提高预矿化效果。